“We told the client to let his family, who is still into this craft, use their talent, and, in turn, and we would use these various forms of the traditional vernacular material in the restaurant,” state the architects who are known to creating a design that is both, high on environment-sensitivity and aesthetics. The attempt, then, became to build up this connection, heritage, and talent in the new venture. With the use of local organic materials - especially clay - local craft and labor, it is an attempt on the architects’ part to acknowledge the consumerism of today’s world, and in a small way, contribute to minimizing the waste generated by prevalent urban attitudes and lifestyles.īy a wonderful coincidence, the respectfulness towards resources and earth-energies that are the founding principles of The Grid Architects’ practice converged with the owners’ family links to pottery, and its inextricable connections to the earth. The project facilitates the basic human need of socializing in an ambiance that respects the earth. Their latest project is a restaurant named Mitti Ke Rang, located in Ahmedabad, Gujarat, India. Therefore, their designs are founded in simplicity and clarity, and create structures that are closely connected to the earth. They have set a mandate for contextual design, something that is timeless. Snehal has done his Masters in sustainability and Bhadri is an Interior designer from APIED Vidyanagar Gujarat. Established about 15 years back, and headed by Snehal Suthar and Bhadri Suthar, tHE gRID Architects is a multidisciplinary design firm which incorporates an array of design combinations and experiences, qualification and skills and deeply committed to excellence. THE gRID is an architecture firm based in Ahmedabad, Gujarat, India. You must see 000X where X is the current version of the MITT firmware.“Mitti Ke Rang” is a restaurant located in Ahmedabad, Gujarat, India designed by Snehal Suthar and Bhadri Suthar of tHE gRID Architects. Notice the seven segment on the MITT board. The preceding output shows a successful installation of the second MITT firmware image. The second chip's firmware cannot be updated until the first chip is installed. Run MuttUtil.exe –UpdateFirmware again for the second chip, after the first firmware update is complete. The preceding output shows a successful installation of the first firmware image. The firmware is updated only if MuttUtil has newer firmware. MuttUtil compares the version of the firmware on the board with the firmware version contained within MuttUtil. If you are using the FPGA development board, the EEPROM can take up to 5 minutes to program. There are two separate chips that require firmware on the MITT board. The preceding output shows that the WinUSB loaded as the device driver for the board. In a command prompt from Program Files\MITT\, run this command: Ignore the warning about the driver might be compatible with the hardware. Under Model select USB MUTT DEFAULT from the list and click Next.Ĭlick Yes and install the driver. on the Select the device driver you want to install for this hardware page.īrowse to the MITT installation directory (Program Files\MITT\ or Program Files (x86)\MITT\ ) in the Install From Disk dialog and click Ok. Select Show All Devices and click Next in the Select your device's type from the list below page.Ĭlick on Have Disk. Select Let me pick from a list of device drivers on my computer. Select Browse my computer for driver software in the Update Driver Software dialog. Right-click on the node and choose Update Driver Software. In Device Manager, locate the device node. Make sure that the board power switch (next to the audio jack) is turned on. We recommend that you use root hub ports and avoid controllers with embedded hubs. Install MITT firmwareĬonnect the MITT board to a USB 2.0 port on the host computer. For more information, see Debugging Tools for Windows (WinDbg, KD, CDB, NTSD) and Windows Debugging. Debugging tools are installed with the WDK. The system under test must be connected to a kernel debugger. The runtime is installed here %ProgramFiles(x86)%\Windows Kits\8.1\Testing\Runtimes\TAEF For complete installation instructions, follow the steps described in WDTF Runtime Library.ĭownload location: WDK and WinDbg downloads When you install the Windows Driver Kit (WDK), the runtime is installed automatically. To run the MITT tests, you need Windows Driver Test Framework (WDTF). If your SUT is a phone, then the host computer, SUT, and MITT board must be configured as shown in this image.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |